SN1L4-103 [KYOCERA AVX]
Feed Through Capacitor, 1 Function(s), 200V, 10A,;型号: | SN1L4-103 |
厂家: | KYOCERA AVX |
描述: | Feed Through Capacitor, 1 Function(s), 200V, 10A, |
文件: | 总6页 (文件大小:85K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Bolt Style EMI Filters
SN Series – 12-32 Thread - Hermetically Sealed –
Circuits Available – C, L, ¹
APPLICATIONS
The SN series offers effective filtering
from 1 MHz to 10 GHz. Glass sealed on
both ends for hermeticity, this series is
impervious to high moisture, solvents, or
other severe environmental conditions
commonly encountered in military applica-
tions. It is designed for bulkhead mounting
with nut and lockwasher supplied.
no-load to full rated load. They are most
effective when placed in high impedance
circuits. The ¹-section designs exhibit
sharper roll-off in filter characteristic and
perform effectively when used in medium
to low impedance circuits.
Alternate lead configurations or special
capacitance values and voltage ratings
may be ordered.
The feedthru designs yield constant filter-
ing as current level is increased from
CHARACTERISTICS
• The hermetic bolt-style design was
developed to meet or exceed the
applicable portions of MIL-F-28861/10.
The filter is assembled with a glass her-
metic seal on both ends. The rugged
monolithic capacitor element is a low
inductance design that yields superior
bypass performance. The ¹-section
design contains two capacitor elements
together with a ferrite bead inductor.
• Certain feedthru designs are rated for
115 VAC/400 Hz applications. The 200
VDC ¹-section design is rated for DC
applications only.
SPECIFICATIONS
1. Plating: Silver standard – Electro-tin or gold
available
STANDARD CONFIGURATION
2. Material:
Case: Cold rolled steel standard, brass available
Leads: Copper nailhead standard. Only available
in .032" diameter. Beryllium copper lead
available. Straight lead available.
3. Operating Temperature Range:
-55°C to +125°C
.220
MAX.
.250
±.010
.216-32 UNEF-2A
(12-32)
.040
MAX.
.032 ±.002
4. Electrical Characteristics:
A. Capacitance: Guaranteed Minimum Value
(GMV) as listed
B. Insulation Resistance:
.250
±.005
.311
±.005
At 25°C: 1,000 megohm-microfarad
min., or 100,000 megohms
.343
±.020
.921
±.020
min., whichever is less
At 125°C: 100 megohm-microfarad
min., or 10,000 megohms
CIRCUIT DIAGRAMS
min., whichever is less
C. Dielectric Withstanding Voltage (DWV):
R-level designs:
2.0 times rated voltage
Class B, Class S designs:
L2
C
Pi
2.5 times rated voltage
SN2
SN1
SN3
D. DC Resistance (DCR): .01 ohm, maximum
E. Voltage Drop: 0.1 volt, maximum
F. Dissipation Factor (DF): 3% maximum
G. Rated Current: 10 Amps, maximum
5. Seal: In accordance with MIL-F-28861.
Leakage rate for Class S designs shall not
exceed 1 x 10-7 atm cc/sec.
Notes:
millimeters (inches)
0.05 (.002) 1.85 (.073)
0.13 (.005) 3.99 (.157)
0.18 (.007) 5.49 (.216)
0.25 (.010) 6.12 (.241)
0.51 (.020) 6.35 (.250)
0.58 (.023) 7.90 (.311)
0.79 (.031) 8.71 (.343)
0.81 (.032) 9.45 (.372)
1.02 (.040) 9.73 (.383)
1.14 (.045) 23.39 (.921)
1. Metric equivalent dimensions
given for information only.
6. Marking: Standard (AVX symbol, AVX part
number)
7. Installation: Filter is supplied with mounting nut
and lockwasher. The recommended mounting
torque is 64 oz-in. ± 4 oz-in. Refer to the
“Installation and Handling” section for additional
information.
1.60 (.063)
—
—
(See Note 1)
27
Bolt Style EMI Filters
SN Series – 12-32 Thread - Hermetically Sealed –
Circuits Available – C, L, ¹
SPECIFICATIONS
Insertion Loss2 Per MIL-STD-220, +25°C
AVX
P/N
1
10
MHz
100
MHz
200
MHz
1
GHz
10
GHz
CKT
C
CAP1
.20
Voltage
50
DCR
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
.01
MHz
SN1C1-204
SN2C1-204
SN3C1-124
SN1A1-503
SN1A1-104
SN2A1-503
SN3A1-753
SN1L1-102
SN1L1-502
SN1L1-103
SN1L1-253
SN2L1-102
SN2L1-502
SN2L1-103
SN3B1-152
SN3B1-123
26
26
20
15
20
15
18
–
39
38
38
35
38
36
38
4
52
65
70
42
48
54
70
20
34
35
36
20
35
35
20
60
60
70
70
50
53
60
70
25
41
40
44
27
41
38
45
70
70
70
70
70
70
70
70
40
50
55
64
45
55
65
70
70
70
70
70
70
70
70
70
50
55
60
70
70
70
70
70
70
L2
¹
.20
50
.12
50
C
.05
100
C
.10
100
L2
¹
.05
100
.075
1000
5000
.01
100
C
200*
200*
200*
200*
200*
200*
200*
200
C
–
15
21
28
4
C
4
C
.025
1000
5000
.01
8
L2
L2
L2
¹
–
–
15
21
8
4
1500
.012
–
¹
200
–
12
* Rated 200 VDC or 125 VAC/400 Hz
1
Decimal point values indicate capacitance in microfarads.
Non-decimal point values indicate capacitance in picofarads.
2
Insertion loss limits are based on theoretical values.
Actual measurements may vary due to internal capacitor
resonances and other design constraints.
28
Screw & Locking Washer Table
HEX NUT AND INTERNAL TOOTH LOCKWASHER
THREAD
A
B
C
D
HEX NUT
WASHER
Size Thread
Hex Nut
Lockwasher
A
B
C
D
4-40 UNC-2B
(.112-40)
.187*
.180
.257
.241
.067*
.057
.083
.073
.225*
.215
.265
.255
.020*
.010
.018
.012
(STD)
(ALT)
8-32 UNC-2B
(.164-32)
.250*
.241
.313
.307
.083*
.073
.114
.104
.285*
.275
.336
.325
.025*
.015
.025
.015
(STD)
(ALT)
10-32 UNF-2B
(.190-32)
.250
.241
.345
.336
.080
.070
.130
.120
.311
.300
.381
.370
.023
.013
.027
.017
(STD)
(ALT)
12-32 UNEF-2B
(.216-32)
.250
.241
.250*
.241
.083
.073
.073*
.063
.383
.372
.383*
.372
.023
.013
.023*
.013
(STD)
(ALT)
1/4-28 UNF-2B
(.250-28)
.311*
.308
.096*
.091
.408*
.396
.021*
.015
5/16-24 UNF-2B
(.312-24)
.377*
.365
.096*
.091
.435*
.425
.027*
.017
*Used for MIL-F-28861 units.
Thread
Recommended Mounting Torque
(.112-40)
4-40 UNC-2A
32 oz-in. ± 4 oz-in.
(.164-32)
64 oz-in. ± 4 oz-in.
64 oz-in. ± 4 oz-in.
64 oz-in. ± 4 oz-in.
44 oz-in. ± 4 oz-in.
60 oz-in. ± 4 oz-in.
8-32 UNC-2A
(.190-32)
10-32 UNC-2A
(.216-32)
12-32 UNEF-2A
(.250-28)
1/4-28 UNF-2A
(.312-24)
5/16-24 UNF-2A
4
How To Order
Notes
NOTE 1:
CAPACITANCE CODE
All AVX Filters part numbers, with exception of certain cylin-
drical styles, show total filter capacitance using the 3-digit
EIA code. The first two digits are significant: the last digit is
the multiplier.
NOTE 4:
VOLTAGE CODES AND FILTER
VOLTAGE RATINGS
IMPORTANT: please contact AVX Filters Applications
Engineering when considering DC-rated filter designs for
possible use in AC applications. As a general rule, DC
designs may be derated for AC applications. Let us assist
you.
Example:
103=10000 picofarads
125=1200000 picofarads
(1.2 microfarads)
The voltage code letters must be selected consistent with
the capabilities as outlined in the product selection tables for
a given filter type. It is important to note that the same code
letter may signify a different voltage rating depending upon
filter type. For example: the “L” code signifies a 200
VDC/125 VAC rating for a bolt-style filter, but it describes a
300 VDC/125 VAC design when applied to a JD-style filter.
It is important to note that ¹ filters and multisection filters are
described using the EIA code from the standpoint of total
capacitance. Capacitance is understood to be specified
as “guaranteed minimum value” (GMV) unless otherwise
specified. AVX Filters can supply ±20% or other specified
tolerances at an additional charge. Contact AVX Filters
Applications Engineering for further information.
NOTE 5:
NOTE 2:
RELIABILITY CODES
The customer must select the reliability code to be consis-
tent with the filter application. As a minimum, all catalog
filters are available as R-level designs.
TERMINAL AND LEADWIRE CODES
Non-standard terminal configurations including special
materials or finishes are available. Please indicate a descrip-
tion and/or outline drawing when requesting a non-standard
terminal (code “3”).
Options:
“-” signifies an R-level filter design without the optional
R-level high-rel screening
NOTE 6:
SPECIAL INFORMATION FOR
CYLINDRICAL STYLE FILTERS
“R” R-level design with optional R-level high-rel screening
also specified
L-section filter designs must be specified with regard to
“standard” or “reverse” configuration. The L-section filter is
normally utilized with the capacitor on the high impedance
side of the circuit and the inductor looking into the low
impedance side. Compact filter types such as the BK2
or CK2 button filters with ferrite bead inductors are only
supplied with the bead assembled into the threaded end.
GK2 and JD2 L-section filters are normally supplied with
a schematic or other marking to indicate location of the
inductor.
“B” Class B design with Group A screening per M28861 for
Class B filters
“S” Class S design with Group A screening per M28861 for
Class S (space grade) filters
Please refer to the catalog section on Reliability for additional
information on how to select reliability codes.
NOTE 3:
SPECIAL DESIGN CODE
(ASSIGNED BY AVX FILTERS)
A special suffix to the standard part number will be added by
AVX Filters Applications Engineering to describe special
designs or designs that are controlled by customer specifi-
cations. It is important to note that even in those instances
where a customer drawing describes a standard catalog
design it is AVX Filters policy to assign a special part number
to the customer drawing for configuration control.
AC-rated catalog designs incorporate reduced values of
capacitance to limit reactive current heating (and subsequent
filter temperature rise) to safe levels. Do not specify a
DC-rated filter with larger capacitance for an AC application
without contacting AVX Filters Applications Engineering.
51
How To Order
Part Number Construction
SOLDER-IN STYLE
Z
S
2
C
2
–
1
0
3
H
X
X
Glass Seal
Orientation
S - Standard
R - Reverse
Q - Hermetic
(Glass Both
Sides)
N - No Glass
(Epoxy Both
Sides)
Voltage
A - 100 VDC
B - 200 VDC
C - 50 VDC
E - 400 VDC/
230 VAC
F - 500 VDC
G - 1000 VDC
K - 250 VDC
L - 300 VDC or
200 VDC/
Reliability
Code
See Notes
Use “H”
to specify
Hi-
Temperature
(300°C)
Rated
Design
Y - Solder
Basic Style
Circuit
0 - Non-Feed
Thru Post
1 - Feed Thru
2 - L-Section
3-Digit
Capacitor
Code
Special
Design
(Customer
DWG. or QPL
Designation)
Lead
2 - Nickel Iron
(Standard)
3 - Special
4 - Aluminum
zz
Z
Y
X
W
115 VAC
M - 350 VDC
N - 70 VDC
(In pF)
Compatible with
seating flange
(Std. Lead)
5 - Aluminum
Compatible with
seating flange
(Special Lead)
D - Aluminum
Compatible with
centering flange
(Std. Lead)
E - Aluminum
Compatible with
Centering flange
(Special Lead)
F - Aluminum
Compatible with
Special Design
BOLT STYLE
SB
2
A
1
–
1
0
3
X X
Reliability
Code
(-See Note 2)
Special Design
(-See Note 3)
Circuit
1 - Feedthru (C)
2 - L-Section (L)
Voltage
A - 100 VDC
B - 200 VDC
3 - PI-Section (¹) C - 50 VDC
F - 500 VDC
G - 1000 VDC
H - 150 VDC
J - 600 VDC
K - 250 VDC
L - 200 VDC/
Basic Style
SA-4-40
SG-6-32
SB-8-32
SM-8-32
SH-10-32 Epoxy Sealed
SJ-12-28 Epoxy Sealed
SC-12-32 Epoxy Sealed (.187 Hex)
SP-12-32 Epoxy Sealed (.250 Hex)
SN-12-32 Hermetic Sealed
SL-1/4-28 Epoxy Sealed
3-Digit Capacitor
Code
(-See Note 1)
Terminal
1 - Copper
2 - Steel
3 - Special Lead
Design
125 VAC
M - 350 VDC
N - 70 VDC
Epoxy Sealed
Epoxy Sealed
Epoxy Sealed
Hermetic Sealed
4 - Beryllium
Copper
SD-5/16-24 Epoxy Sealed
SF-5/16-32 Epoxy Sealed
52
How To Order
Part Number Construction
CYLINDRICAL STYLE
G
K
2
A
A
–
S07
XX
Thread
Length
A - .187" (See Notes)
B - .312"
Reliability
Code
Special Design
(Customer DWG.
or QPL
Basic Style
A - Button Type
(.410 Dia.)
B - Button Type
(.375 Dia.)
Thread Type
K - 1/4-28 Herm 0 - Feedthru Lead A - 100 VDC
Seal
L - 1/4-28 Epoxy
Seal
M - 8-32 Herm
Seal
N - 12-32 Herm
Seal
Circuit
Voltage
(without
Capacitor)
1 - Feedthru
Capacitor
2 - L-Section
Filter
B - 200 VDC
C - 50 VDC
E - 400 VDC/
230 VAC
F - 500 VDC
G - 1000 VDC
H - 150 VDC
J - 600 VDC
K - 250 VDC
L - 200 VDC/
125 VAC
Designation)
Feedthru’s &
BK2, CK2
All Other
Circuit Types
C - Extended
Button
G - .375" Dia.
J - .690" Dia.
H - .410" Dia.
F - .250" Dia.
Q - Special
X X X
Capacitance In
Picofarads
3 - PI Filter
4 - T-Section
T - 1/4-28
Post Terminal 5 - Double
(Both Ends)
V - 1/4-28 Post 6 - Five Element
and Flag
Terminal
X - 1/4-28 Hex
Adaptor
Current Rating
L-Section
Circuit
Code
Current
S - Standard L
(Inductor at
Thread End)
R - Reverse L
(Capacitor at
Thread End)
P - PI-Circuit
M - Multi
01
02
03
04
05
06
07
08
09
10
11
12
16
17
18
19
.06 AMP
.1
Cap Input
7 - Five Element
IND Input
8 - Special Ckt.
Design
(Except JD
Series
300 VDC/
.15
.25
.3
.45
.5
1
2
3
5
10
4
6
.75
1.5
125 VAC)
M - 350 VDC
N - 70 VDC
Section
T - T Circuit
Please contact the factory for Filter Plates
and other custom product part numbers.
NOTICE: Specifications are subject to change without notice. Contact your nearest AVX Sales Office for the latest specifications. All statements, information and
data given herein are believed to be accurate and reliable, but are presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements or suggestions concerning possible use of our products are made without representation or warranty that any such use is free of patent infringement
and are not recommendations to infringe any patent. The user should not assume that all safety measures are indicated or that other measures may not be
required. Specifications are typical and may not apply to all applications.
53
相关型号:
©2020 ICPDF网 联系我们和版权申明